How To Cut A 135 Degree Angle On A Miter Saw
To cut a 135-degree angle you need to be familiar with the first one the miter angle.
To adjust the angle you need to use a knob and lever that is located at the front of the saw. It allows you to swing the cutting head as well as the table side-to-side.
You also have to adjust the bevel angle and that’s done using the start-shaped knob at the back of the saw.
As per users, a 135-degree angle cut can be too hard than regular corner cuts. Here we have described some steps on how to cut a 135-degree angle on a miter saw.
The List Of How To Cut A 135 Degree Angle On A Miter Saw
Step 1 - Set The Miter Saw
The outside 135-degree corner is very much like an outside 90-degree corner when using a transition piece. Set your miter angle to 11 and a quarter degrees for all your cuts.
You can also go around the corner without a transition piece and just set your saw at 22 and a half degrees for more details on making a transition piece follow outside a 90-degree corner.
Step 2 - Cut at 45/2 = 22.5 Degrees Angle
You usually can see 135 corners where the two walls come together with a sharp edge either way. Your corners can be cut in the same manner.
The molding is actually only turning 45 degrees each molding piece that comes together to make the corner contributes equally. So each only has to cut at a twenty-two as well as a half-degree angle.
Step 3 - Right Angle Position
You also can cut all of the corners. To make an accurate cut you need to change the miter angle. Therefore, if you are going to place your molding in the saw with the lip that touches the ceiling pressed flat on the saw up against the fence.
The flat part touches the wall pointing it out towards us for the molding coming in from the left side of the corner.
Make sure the saw to the right angle position your molding into place and make your cut with the molding coming in from the right side of the corner.
Step 4 - 22.5 Degree Miter Angle
To make a miter cut on the left side you simply position your saw to the left at the 22 and ½ degree miter angle position.
You mold in place and cut. You can fit together perfectly if you have two pieces of crisp corners. But with the radius of your corner, you need to make some modifications at the bottom of your pieces using a utility knife.
Also, Consider the Below Instructions
Ensure safety: Always wear appropriate safety gear, including safety glasses and ear protection, when operating power tools.
Set the miter angle: Most miter saws have a miter gauge that allows you to adjust the angle of the cut. Look for a knob or lever that loosens the gauge, allowing you to rotate it. Set the gauge to 45 degrees.
Align the workpiece: Place your workpiece on the miter saw table. Ensure that it is firmly pressed against the fence at the back of the table. This will provide stability during the cut.
Make a test cut: It's a good idea to make a test cut on a scrap piece of wood to confirm that the angle is correct before cutting your actual workpiece. This allows you to fine-tune the angle if necessary.
Set the bevel angle: The bevel angle adjustment controls the tilt of the blade. To cut a 135-degree angle, you need to adjust the bevel angle to 45 degrees in the opposite direction of the miter angle. For example, if the miter angle is set to 45 degrees to the right, set the bevel angle to 45 degrees to the left.
Verify the angle: Double-check that the miter and bevel angles are correctly set. Take your time to ensure accuracy.
Make the cut: Once you have confirmed the angles, bring the saw blade down onto your workpiece, starting at the front edge. Hold the workpiece securely against the fence and gradually push it forward through the blade. Maintain a steady and controlled motion throughout the cut.
Check the cut: After completing the cut, inspect the workpiece to ensure the angle is correct. Use a protractor or angle finder if necessary to measure the angle of the cut.
Related Tags
how to cut a 140 degree angle on a miter saw, 67.5 degree miter cut, cutting octagon angles on miter saw, how to cut a 120 degree angle on a miter saw, how to cut a 150 degree angle on a miter saw, how to cut a 135 degree angle on a table saw,, how to set miter saw angles.
Final Word:
The article, I hope, will share a clear concept about how to cut a 135-degree angle on a miter saw intensely.
We basically recommend you cut other angles such as 22.5 degrees, 45 degrees, and 90 degrees which will help you to cut a 135-degree angle on a miter saw.
Moreover, you also can make sure of some pretty clean cuts for being a cheap blade.
I think that it might have snapped blade quality up just a touch. A miter saw is not only perfect for a variety of cuts but it also leads to a large number of manufacturers and innovation improvements. If any problem, feel free and contact us.
Tanya B. Clark
Hey everybody! I live my life by writing. #writer. I write on everything and anything that spikes any hint of interest in me! Do check my blogs out!
